Tankless vs Tank Water Heater: Specs & Sizing Guide
Last updated
Quick Answer
Comparing a tankless vs tank water heater starts with how your household draws hot water. A storage tank keeps a preheated reserve; a tankless heater stores none, so it avoids standby losses, but it needs a minimum flow (typically 0.5 GPM in the guide cited here) before it fires (Consortium for Advanced Residential Buildings / Steven Winter Associates, Tankless Water Heaters, 2009, pp. 1–2, Accessed 2026-11-15).
This guide contains no affiliate links and no paid placements.
Choose a storage tank water heater when your home already has a Category I gas vent or a suitable electric water-heater circuit and you want steady multi-fixture peak delivery. Even for a like-for-like swap, confirm the existing vent: Bradford White's manual for its draft-diverter gas tank says to inspect the venting system of a replacement installation and notes that when an existing Category I appliance is replaced, the original venting system may no longer be sized to vent the attached appliances (Bradford White, Manual 238-51007-00R, p. 7, Accessed 2026-11-15). Choose a condensing gas tankless water heater when wall space is tight, continuous hot-water draw matters more than retrofit simplicity, and you are prepared to follow the owner's manual's descaling guidance if your water is hard. A 2009 guide notes that electric tankless systems have low heating capacity and need a higher-capacity electrical panel because of their high amp draw, and it does not recommend them (CARB / Steven Winter Associates, Tankless Water Heaters, 2009, p. 1, Accessed 2026-11-15), so confirm electrical capacity before considering one. Hybrid electric heat pump tanks vary by model: A. O. Smith's Voltex AL sheet lists a 208/240 VAC, 30 amp supply (A. O. Smith, AOSXE50010, p. 2), Rheem's Hybrid Builder sheet lists 208–240 volts at 24 amps with a 30-amp breaker size (Rheem, Form HP-310BM Rev. 4, p. 1), and ENERGY STAR's criteria include a separate integrated-unit category for a 120 volt / 15 amp circuit (ENERGY STAR, Key Product Criteria, Accessed 2026-11-15). Room-air needs are also model-specific; see the table below.
How we chose what to mention Brands and product lines appear solely as technical examples of published residential specifications—not as rankings or endorsements: 1. First-party technical documentation: Official manufacturer specification sheets or manuals opened on 2026-11-15. 2. Standardized federal test metrics: Published Uniform Energy Factor (UEF), First-Hour Rating (FHR), or gallons-per-minute (GPM) figures under 10 CFR Part 430, Subpart B, Appendix E. 3. Residential-use examples: Product documents that publish residential specifications. Some are also marketed for commercial use (Navien's NPE-A2 page lists models as "Residential/Commercial"), and each model's own installation manual sets its gas, electrical, and venting requirements. 4. Documented installation limits: Explicit venting, gas-pipe, clearance, and maintenance rules.
How Storage Tank and Tankless Water Heaters Deliver Hot Water
ENERGY STAR criteria for both designs use Uniform Energy Factor (UEF), which is determined by the Department of Energy test method in 10 CFR Part 430, Subpart B, Appendix E, while the ENERGY STAR sizing metrics differ by type (ENERGY STAR, Key Product Criteria, Accessed 2026-11-15):
- Storage tanks use First-Hour Rating (FHR): FHR measures maximum hot-water delivery in gallons during one hour of operation starting with a fully heated tank, measured at a 125°F outlet temperature in the Uniform Energy Factor test method. ENERGY STAR criteria require gas storage models to reach at least 51 gallons per hour and electric heat pump water heaters to reach at least 45 gallons per hour (ENERGY STAR, Key Product Criteria, Accessed 2026-11-15).
- Tankless units use Gallons Per Minute (GPM) at a 67°F rise: Max GPM measures sustainable flow across a 67°F temperature rise (for example, 58°F inlet to 125°F outlet). ENERGY STAR criteria for residential gas instantaneous units under 200,000 Btu/h require at least 2.8 GPM over a 67°F rise and a UEF of 0.95 or higher (ENERGY STAR, Key Product Criteria, Accessed 2026-11-15).
A 2009 technical guide from the Consortium for Advanced Residential Buildings and Steven Winter Associates (CARB / SWA), hosted on a U.S. Department of Energy website, highlights two operational traits of tankless units: they require a minimum flow rate (typically 0.5 GPM) before they fire, and an additional electric connection is typically needed for tankless gas water heaters, so such a unit will not function during a power outage. The guide notes at least one model that has a hydro-generated ignition (CARB / SWA, Tankless Water Heaters, 2009, p. 2, Accessed 2026-11-15). Check the specific model's manual for its power requirements.
Frequent on/off operation can also introduce cold water into the hot-water line, which Navien's page calls the "cold-water sandwich effect." To address this, Navien states on its NPE-A2 series page (models NPE-180A2, NPE-210A2, and NPE-240A2) that the series includes a buffer tank and a built-in recirculation pump and offers up to a 15:1 turndown ratio (TDR) (Navien, NPE-A2 Series, Accessed 2026-11-15).
Side-by-Side Specification Comparison: Storage Tank vs. Tankless
The table below compiles ENERGY STAR criteria and manufacturer specifications opened in November 2026. The ENERGY STAR rows state program criteria. The venting, supply, and drainage rows describe only the specific manufacturer documents named in each cell, not every model in a category. If your current unit is failing, review how to decide between water heater repair and replacement.
| Attribute | Gas Storage Tank | Condensing Gas Tankless | Hybrid Electric Heat Pump Tank |
|---|---|---|---|
| Primary sizing metric | FHR ≥ 51 gal/hr for ENERGY STAR (ENERGY STAR Criteria) | Max GPM ≥ 2.8 at 67°F rise for ENERGY STAR (ENERGY STAR Criteria) | FHR ≥ 45 gal/hr for ENERGY STAR (ENERGY STAR Criteria) |
| ENERGY STAR minimum UEF | ≥ 0.81 (tank > 20 and ≤ 55 gal, Medium Draw); ≥ 0.86 (High Draw, or tank > 55 gal) | ≥ 0.95 (< 200,000 Btu/h gas instantaneous) | ≥ 3.30 (integrated HPWH); ≥ 2.20 (integrated HPWH on a 120V/15A circuit, or split system) |
| ENERGY STAR warranty floor | ≥ 6 years on system (including parts) | ≥ 6 years on heat exchanger, ≥ 5 years on parts | ≥ 6 years on sealed system |
| Venting (cited models) | Category I appliance connected to a lined masonry chimney or a venting system approved by local codes (Bradford White Manual, pp. 7–8) | 2" PVC up to 75 ft (Navien NPE-A2 Series page); other models and vent materials per their own manuals | Electric unit. Room-air needs are model-specific: A. O. Smith Voltex AL lists a 450 ft³ minimum for an enclosed room, 84 ft³ with louvers, and no minimum with inlet and outlet ducting (p. 3); Rheem Hybrid Builder lists a full louvered door or two louvers for non-ducted units in rooms smaller than 700 ft³ (p. 3) |
| Gas / electrical supply (cited models) | Gas supply lines per the National Fuel Gas Code; ≥ 3" drip leg (sediment trap) and a ground joint union (Bradford White Manual, p. 12) | Navien NPE-A2 maximum input of 150,000 to 199,900 Btu/h; Navien lists 1/2" gas up to 24 ft; electrical requirements per the model manual | A. O. Smith Voltex AL: 208/240 VAC, 30 amp supply (p. 2); Rheem Hybrid Builder: 208–240 V, 24 amps, 30-amp breaker size (p. 1); ENERGY STAR also lists a 120V/15A integrated-unit category |
| Condensate drainage (cited models) | Model-specific; the cited Bradford White manual describes a T&P discharge line (p. 10) and a drain pan where leakage could cause damage (p. 5) | Model-specific; not stated on the Navien series page cited here | Non-acidic condensate drain, or a condensate pump if no suitable drain is available (A. O. Smith Voltex AL, p. 2) |
Sizing Simultaneous Fixture Draws and Inlet Water Temperatures
A tankless heater supplies continuous hot water only up to its instantaneous flow ceiling at your cold-water inlet temperature. The 2009 CARB / SWA guide lists typical end-use flow rates: bathroom sinks draw 0.5–1.5 GPM, showerheads draw 1.5–2.5 GPM, kitchen sinks draw 1.0–2.5 GPM, dishwashers draw 1.0–3.0 GPM, and bathtubs draw 2.0–4.0 GPM (CARB / SWA, Tankless Water Heaters, 2009, p. 2, Accessed 2026-11-15).
Running two 2.0 GPM showers and a 1.5 GPM sink requires 5.5 GPM: - At a 58°F inlet and 125°F outlet (67°F rise), the temperature rise equals the 67°F rise at which ENERGY STAR's Max GPM metric is measured, so a unit's published Max GPM at a 67°F rise can be compared directly with the 5.5 GPM demand (ENERGY STAR, Key Product Criteria, Accessed 2026-11-15). - As a hypothetical, if inlet water were 45°F (an 80°F rise to reach 125°F), deliverable GPM would drop accordingly, because thermostatically controlled tankless units vary their output temperature according to flow rate and inlet water temperature (CARB / SWA, Tankless Water Heaters, 2009, p. 1, Accessed 2026-11-15).
Storage tanks absorb simultaneous spikes from stored reserve first: A. O. Smith's Voltex AL heat pump models (HPTS-50 / HPTS-66) list FHRs of 65 and 82 gallons (A. O. Smith, AOSXE50010, Sept. 2025, p. 2), and Rheem's 208–240V Hybrid Builder (PRO H50 T2RH310BM / PRO H65 T2RH310BM) lists 67 and 75 gallons (Rheem, Form HP-310BM Rev. 4, p. 1, Accessed 2026-11-15). For broader manufacturer context, see our water heater brand comparison.
Gas Piping, Venting, and Clearances in Replacement Jobs
Replacing a storage tank with tankless equipment can affect three infrastructure systems, and the requirements differ by model. The examples below come from specific manufacturer documents:
- Exhaust venting: Bradford White's manual for its draft-diverter gas tank describes a Category I appliance that connects to a lined masonry chimney or a venting system approved by local codes. It says horizontal runs should slope upward not less than 1/4 inch (21 mm/m) from the appliance to the vent terminal, and that the heater must not be vented into the venting system of another gas appliance designed to vent under positive pressure (Bradford White, Manual 238-51007-00R, Rev. 07/26, pp. 7–8, Accessed 2026-11-15). The 2009 CARB / SWA guide notes that tankless venting "can be expensive (Category 3 stainless steel)" and suggests locating the unit on an exterior wall to minimize vent length (p. 2); that is a general 2009 note, and a current model's manual governs. Navien's
NPE-A2page lists 2-inch PVC venting up to 75 feet (Navien, NPE-A2 Series, Accessed 2026-11-15). - Gas piping and sediment traps: Compare the existing heater's input on its rating plate with the new model's input. Navien's page lists maximum inputs of 150,000 Btu/h (
NPE-180A2), 180,000 Btu/h (NPE-210A2), and 199,900 Btu/h (NPE-240A2) and states 1/2-inch gas pipe up to 24 feet for the series. Pipe sizing for other lengths and for the total gas load should come from the manufacturer's installation instructions and the National Fuel Gas Code, which Bradford White's manual cites for gas supply lines. That manual also specifies a drip leg (sediment trap) of at least 3 inches installed as close to the water heater's gas valve as possible and a ground joint union as close to the water heater as possible in the gas supply line (Bradford White, Manual 238-51007-00R, p. 12, Accessed 2026-11-15). - Drain pans and relief clearances: Where a leak could damage the area adjacent to the heater or lower floors and the location cannot be avoided, Bradford White's manual calls for a drain pan with a length and width at least 4 inches greater than the water heater diameter, piped to an adequate drain with piping at least 3/4 inch in diameter and pitched for proper drainage (p. 5). The manual recommends a minimum 4 inches of side clearance for servicing the T&P relief valve (Bradford White, Manual 238-51007-00R, pp. 5–6, 10, Accessed 2026-11-15).
Regional Context: Hard-Water Scale and Inlet Temperatures in Phoenix and San Antonio
Utility reports for two cities show how much hardness and water temperature can vary from place to place, so check your own utility's report. USGS notes that when hard water is heated, such as in a home water heater, solid deposits of calcium carbonate can form, and that this scale can reduce the life of equipment, raise the costs of heating the water, lower the efficiency of electric water heaters, and clog pipes (USGS, Hardness of Water, Accessed 2026-11-15).
- Hardness examples: USGS classifies 121 to 180 mg/L as calcium carbonate as "hard" and more than 180 mg/L as "very hard" (USGS, Hardness of Water, Accessed 2026-11-15). Phoenix's 2025 Water Quality Report lists total hardness of 172–302 ppm (10–17.6 grains per gallon) in distribution-system samples (City of Phoenix, 2025 Water Quality Report, p. 4, Accessed 2026-11-15), while San Antonio Water System (SAWS) states that the typical hardness of its water is 15–20 gpg (SAWS, Water Quality FAQs, Accessed 2026-11-15). The sources use different units, so compare like with like when reading your own utility's report.
- Scale maintenance on coils vs. tanks: The 2009 CARB / SWA guide says that at higher temperature settings with high mineral content, scaling of a tankless unit's low-mass heat exchanger is likely, that the heating coils should be flushed with a descaling solution, and that owners should refer to the owner's manual for specific maintenance requirements (CARB / SWA, 2009, p. 2). Navien's
NPE-A2page describes dual stainless steel heat exchangers; descaling requirements should come from the model's owner's manual. For storage tanks, Bradford White's manual for its draft-diverter gas tank lists checking the T&P valve lever at least once a year, draining off a gallon monthly to remove silt and sediment, and inspecting the anode rod about every 2 years, with more frequent anode inspection when using softened (or phosphate treated) water (Bradford White, Manual 238-51007-00R, p. 21, Accessed 2026-11-15). See our hard-water water heater protection guide. - Inlet and ambient temperatures: Phoenix's 2025 report lists distribution-system sample temperatures of 47–92°F (City of Phoenix, 2025 Water Quality Report, p. 4). That is a sample range across the year, not a design inlet temperature; for sizing, confirm the cold-water temperature at your own home in the coldest part of the year and compare it with the unit's published flow-versus-temperature-rise data. Heat pump models also list ambient-air limits: Bradford White's AeroTherm Series G2 sheet lists a heat pump operating air temperature range of 37–120°F and says the unit defaults to its electric heating elements outside that range (Bradford White, Form 1903, p. 1, Accessed 2026-11-15), and A. O. Smith says its Voltex AL heat pump can work down to 37°F (A. O. Smith, AOSXE50010, p. 1).
Homeowner Pre-Quote Inspection Checklist
- [ ] Rating plate details: Record current tank gallons, fuel type, Btu/h or kW input, and age.
- [ ] Peak simultaneous GPM: Sum fixtures likely to run together during morning or laundry peaks.
- [ ] Vent routing: Note whether the existing venting runs to a chimney or roof vent or sits near an exterior wall, and estimate the route length; the new model's installation manual determines which vent materials, diameters, and lengths are approved.
- [ ] Gas line diameter and run: Record the existing gas pipe diameter serving the location and estimate the distance to the meter; the new unit's manual sets the required pipe size.
- [ ] Power and drainage: Note the electrical supply near the unit (voltage, breaker size, available outlet) and floor or condensate drain access; the model's manual sets its requirements.
- [ ] Local hardness: Check your city's Water Quality Report for hardness so descaling needs can be discussed with the provider.
Connecting with a Local Plumbing Provider
Gas-line sizing, flue or PVC vent routing, condensate drainage, thermal-expansion protection, and local permit requirements depend on the specific model and your home, so they are best confirmed in an on-site evaluation against the model's installation manual and local requirements. You can connect with an independent local provider via our water heater repair and replacement referral page.
PlumbRoute is a referral service that connects homeowners with independent local plumbing providers; PlumbRoute does not perform plumbing, gas-fitting, or electrical work directly. Pricing, equipment availability, permitting, warranty terms, and scheduling are set independently by participating providers.
Sources
- Water Heater Key Product Criteria, ENERGY STAR (an official U.S. government website), https://www.energystar.gov/products/water_heaters/residential_water_heaters_key_product_criteria (Accessed 2026-11-15).
- Tankless Water Heaters (last update 8-18-2009), Consortium for Advanced Residential Buildings and Steven Winter Associates, Inc., hosted on a U.S. Department of Energy website, https://www1.eere.energy.gov/buildings/publications/pdfs/building_america/tankless_water_heaters.pdf (Accessed 2026-11-15).
- NPE-A2 Series: Tankless Water Heaters with Recirculation Pump, Navien Inc., https://www.navieninc.com/series/npe-a2 (Accessed 2026-11-15).
- Installation and Operation Manual: Gas-Fired Water Heater (238-51007-00R Rev. 07/26), Bradford White Corporation, https://docs.bradfordwhite.com/I&O/238-51007-00_Current.pdf (Accessed 2026-11-15).
- Voltex AL Smart Hybrid Electric Heat Pump Water Heater (AOSXE50010, September 2025), A. O. Smith Corporation, https://assets.hotwater.com/damroot/Original/10004/AOSXE50010.pdf (Accessed 2026-11-15).
- Residential Hybrid Electric Heat Pump-Builder Water Heaters Specification Sheet (Form HP-310BM Rev. 4, 06/23), Rheem Water Heating, https://media.rheem.com/site/rheemdotcom/resources/HP-310BM%20Rev4%20GEN%20V%20Builder%20SS_1.pdf (Accessed 2026-11-15).
- AeroTherm Series G2 Hybrid Electric Heat Pump Water Heater Specification Sheet (Form 1903, 05/26), Bradford White Corporation, https://docs.bradfordwhite.com/Spec_Sheets/1903_Current.pdf (Accessed 2026-11-15).
- Hardness of Water, U.S. Geological Survey, https://www.usgs.gov/water-science-school/science/hardness-water (Accessed 2026-11-15).
- 2025 Water Quality Report, City of Phoenix Water Services Department, https://www.phoenix.gov/content/dam/phoenix/waterservicessite/documents/wsdprimarywqr.pdf (Accessed 2026-11-15).
- Water Quality FAQs, San Antonio Water System, https://www.saws.org/your-water/water-quality/saws-water-quality-concerns/faqs/ (Accessed 2026-11-15).
Still dealing with this issue? You can request a connection with an independent local plumbing provider — there is no fee to submit a request.
Request a ConnectionFrequently asked questions
Related services
PlumbRoute connects a homeowner's request with independent local providers. Requesting a connection is free and carries no obligation to hire.
Looking for water heater repair in your area?
PlumbRoute is a referral service -- request a connection with an independent local plumber serving one of these areas:
Independent Providers · Phoenix AreaWater Heater Repair & Replacement in Scottsdale, AZ
Independent Providers · Scottsdale AreaWater Heater Repair & Replacement in Dallas, TX
Independent Providers · Dallas AreaWater Heater Repair & Replacement in Fort Worth, TX
Independent Providers · Fort Worth AreaWater Heater Repair & Replacement in Plano, TX
Independent Providers · Plano AreaWater Heater Repair & Replacement in Frisco, TX
Independent Providers · Frisco AreaWater Heater Repair & Replacement in Houston, TX
Independent Providers · Houston AreaWater Heater Repair & Replacement in Austin, TX
Independent Providers · Austin AreaWater Heater Repair & Replacement in San Antonio, TX
Independent Providers · San Antonio AreaWater Heater Repair & Replacement in San Diego, CA
Independent Providers · San Diego Area
Need help with this?
Request a connection with an independent local plumbing provider.
PlumbRoute is a referral service, not a plumbing contractor.
Request an Estimate
Tell us about your project so a local provider can follow up with pricing.